ALWAYS DRY: HOW TO USE
Always Dry for Cars
Application Instructions
Pre-treatment
Before applying Semper Seco for cars, it is recommended to wash and polish the vehicle, paying attention to the following recommendations:
-
Cleaning: It is recommended to wash the car, starting from top to bottom, front to back;
-
Wash the car thoroughly, using clean water. Remove any major dirt from the surface of the car;
-
Wash the car with neutral cleaning solution;
-
Wash the car thoroughly, using clean water again.
-
-
For an even better appearance, it is recommended to polish the car before application:
-
Heavy Polishing: Recommended for removing serious scratches before application;
-
Intermediate Polishing: Recommended for removing moderate scuffs and scuffs before application;
-
Light Polishing: Recommended for removing small scratches before application.
-
-
Make sure the car is completely dry before application.
Application
It is recommended to follow the procedure below to apply Semper Seco for cars:
-
Wrap the sponge with the microfiber cloth (included with the product);
-
Put a few drops of Semper Seco coating on the microfiber cloth and rub it evenly over the car's paintwork, once in the horizontal direction and once in the vertical direction;
-
Tip: It is recommended to apply the coating 40 cm at a time, using 3-5 drops.
-
-
After applying, use another new microfiber cloth to rub the surface until smooth. the coated area will have a uniform shine.
-
Tip: Rub the coating starting from the top to the bottom and from the left side to the right. Check to make sure you apply the coating to the entire surface of the vehicle.
-
Important recommendations:
-
It is recommended to apply the Semper Seco coating in a dust-free place and at a temperature between 5�C and 5�C. 30º Celsius;
-
Do not directly apply the Semper Seco coating to the paintwork. This way it will be harder to spread;
-
Do not touch the coating for 24 hours. It is recommended not to use the car for 24 hours after application;
-
Do not wash the car for 7 days.
Post-treatment
When the water repellent function is lost, simply apply the Semper Seco coating again, following the same recommendations ;es, on the previously coated surface.
Always Dry for Glass
Application Instructions
?
Pre-treatment
Before applying Semper Seco to the glass, pay attention to the following recommendations:
-
Wash the glass (windshield, rear view mirror, screen, etc.) thoroughly with glass cleaning solution and clean water;
-
Use a dry cloth or dryer, at low temperature, to dry the glass. Since the second method tends to bring better results;
-
Check if the glass is clean. completely dry before applying the Semper Seco coating.
Application
It is recommended to follow the procedure below to apply Semper Seco for Glass:
-
Apply the Semper Seco coating evenly to the glass surface. Using a microfiber cloth (included with the product) spread the Semper Seco coating evenly over the glass surface. Make sure to spread the Semper Seco coating over the surface evenly, so that it remains transparent;
-
It is recommended to apply the Semper Seco coating once again to the surface, repeating the same process above;
-
Keep the applied surface out of contact with water until dry. ensure that the coating is completely dry. Drying time varies according to the temperature, and it is recommended to wait 4 hours for the Always Dry Glass coating to be completely dry.
Post-treatment
When the water repellent function is lost, simply apply the Semper Seco coating again, following the same recommendations ;es, on the previously coated surface.
Always Dry for Clothing
Application Instructions
?
Pre-treatment
Before applying the Semper Seco coating, pay attention to the following recommendations:
-
Wash the clothing item using clean water before applying the Always Dry coating;
-
Allow the item to dry completely;
-
Check if it is working properly. completely dry before applying the Semper Seco coating.
Application
It is recommended to follow the procedure below to apply Semper Dry for Clothing:
-
Shake the bottle in an upright position. Apply evenly at a distance of 20 cm from the surface of the object to the surface. the same if it gets wet, then repeat the same procedure 2 times. If necessary, use a microfiber cloth to spread the Semper Seco coating evenly over the surface, so that it remains transparent;
-
Let it dry for 20 minutes. Keep the applied surface out of contact with water until dry. ensure that the coating is completely dry. Remember that drying time may vary depending on the temperature.
Post-treatment
If any sprayed item collects dust, just remove it with a damp cloth so as not to damage the coating.
When the water repellent function is lost, simply apply, following the same recommendations, the Semper Seco coating again over the previously coated surface.
Precautions
-
Apply in a place with good ventilation, which is not exposed to hot sun;
-
Apply first to a small area to test;
-
If you need to wash the item, do so separately from other items.
Always Dry Too Much Surfaces
Application Instructions
?
Pre-treatment
Before applying the Semper Seco coating, it is recommended to wash and polish, if necessary, the surface, paying attention to the following recommendations:
-
It is recommended to wash the surface using clean water and neutral cleaning solution;
-
If necessary, you can polish the surface in question.
Application
It is recommended to follow the procedure below to apply Semper Seco:
-
Wrap the sponge with the microfiber cloth (included with the product);
-
Put a few drops of Semper Seco coating on the microfiber cloth and rub it over the surface evenly, once in the horizontal direction and once in the vertical direction;
-
Tip: It is recommended to continue the application 40 cm at a time, using 3-5 drops.
-
-
After applying, use a new, clean microfiber cloth to rub the coating until smooth. the coated area will have a uniform shine.
Important recommendations:
-
It is recommended to apply the Semper Seco coating in a dust-free place and at a temperature between 5�C and 5�C. 30º Celsius;
-
Do not touch the coating for 24 hours;
-
Do not wash the covering for 7 days.
Post-treatment
When the water repellent function is lost, simply apply the Semper Seco coating again, following the same recommendations as before. es, on the previously coated surface.
?
?
?